Description
SOURCE
Lamp: 250 W discharge
Base: GY 9.5
Approved models:
Philips MSD 250/2 (installed as standard) 3000 hr, 8500 K, 250 W
Osram HSD 250/78 3000 hr, 7800 K, 250 W
GE CSD 250/2 3000 hr, 9000 K, 250 W
DYNAMIC EFFECTS
Color mixing: CMY, independently variable 0 – 100%
Color wheel: 6 interchangeable filters (incl. UV transmitter and CTC) + open, indexing, continous rotation
Mechanical dimmer: 0 – 100%
Shutter: Strobe effect up to 14 Hz, pulse effects, instant open and blackout
Diffuser: Variable frost filter
Pan: 540°
Tilt: 257°
CONTROL AND PROGRAMMING
DMX channels: 13/19
Setting and addressing: Control panel with LED display
16-bit control: CMY, color wheel, dimmer, frost, pan and tilt
Movement control options: Tracking and vector
Protocol: USITT DMX512/1990
Receiver: Opto-isolated RS-485
Firmware update: Serial upload via DMX link
PHOTOMETRICS
MAC 250 Wash standard
Total output: 7700 lumens
One-tenth peak output: 6800 lumens
Half-peak output: 3100 lumens
Cutoff angle: 25.9°
One-tenth peak angle: 19.1°
Half-peak angle: 9.1°
Measurement conditions: 226 V, 50 Hz; no effects applied
Measurement source: Philips MSD 250/2
36 MAC 250 Wash
MAC 250 Wash standard with frost
Total output: 4800 lumens
One-tenth peak output: 4100 lumens
Half-peak output: 1900 lumens
Cutoff angle: 48.8°
One-tenth peak angle: 34.8°
Half-peak angle: 16.0°
Measurement conditions: 226 V, 50 Hz; with frost applied
Measurement source: Philips MSD 250/2
MAC 250 Wash wide-angle lens
Total output: 9100 lumens
One-tenth peak output: 8600 lumens
Half-peak output: 4900 lumens
Cutoff angle: 61.5°
One-tenth peak angle: 52.5°
Half-peak angle: 28.7°
Measurement conditions: 232 V, 50 Hz; no effects applied
Measurement source: Philips MSD 250/2
MAC 250 Wash wide-angle lens with frost
Total output: 5100 lumens
One-tenth peak output: 4700 lumens
Half-peak output: 2600 lumens
Cutoff angle: 77.9°
One-tenth peak angle: 65.6°
Half-peak angle: 34.7°
Measurement conditions: 232 V, 50 Hz; with frost applied
Measurement source: Philips MSD 250/2
CONNECTIONS
AC Power input: 3-pin IEC
Data input: locking 3-pin and 5-pin XLR male sockets
Data output: locking 3-pin and 5-pin XLR female sockets
Data pinout: pin 1 shield, pin 2 cold (-), pin 3 hot (+)
THERMAL
Maximum ambient temperature (Ta): 104°F
Maximum surface temperature: 320°F
AC POWER
Operating range: 100 – 250 V, 50/60 Hz
AC input: 3-prong IEC male socket
Typical power and current
100 V, 50 Hz: 319 W, 3.8 A, PF 0.83
100 V, 60 Hz: 317 W, 3.4 A, PF 0.93
120 V, 50 Hz: 320 W, 2.9 A, PF 0.91
120 V, 60 Hz: 314 W, 2.7 A, PF 0.96
208 V, 50 Hz: 320 W, 1.9 A, PF 0.81
208 V, 60 Hz: 319 W, 1.7 A, PF 0.92
230 V, 50 Hz: 323 W, 1.6 A, PF 0.89
230 V, 60 Hz: 326 W, 1.5 A, PF 0.95
250 V, 50 Hz: 326 W, 1.5 A, PF 0.89
250 V, 60 Hz: 325 W, 1.4 A, PF 0.96
V = volts, Hz = hertz, W = watts, A = amps, PF = power factor
Allow for a deviation of +/- 10% from typical figures listed above.
Measurements made at nominal voltage.
MAC 250 Wash™ Specifications 37
Fuses
Main fuse: 6.3 A / 250 V, time-delay – P/N 05020020
Fuse F1: 6.3 A / 250 V, time-delay – P/N 05020020
Fuse F2: 2.0 A / 250 V, time-delay – P/N 05020009
ELECTROMECHANICAL EFFECTS
Cyan filter: 0 – 100%
Magenta filter: 0 – 100%
Yellow filter: 0 – 100%
Color wheel: 6 colors plus open and split positions
Dimmer: 0 – 100%
Shutter: Variable from 0 – 14 flashes per second
Zoom diffuser: 0° – 16°
Pan: 540° in 0.013° steps
Tilt: 257° in 0.007° steps
APPROVALS
EU EMC: EN 55 103-1, EN 55 015, EN 61 547
EU safety: EN 60598-2-17
US safety: ANSI/UL 1573
Canadian safety: CSA C22.2 NO 166
CONSTRUCTION
Housing: UV-resistant fiber-reinforced composite
Ingress protection factor: IP 20
INSTALLATION
Orientation: any
Minimum distance to combustible materials: 4″
Minimum distance to illuminated surfaces: 20″
Minimum center-to-center distance between MAC 250 Wash fixtures: 16.2″
