Description
SOURCE
Lamp: 700 W short arc discharge
Base: Double-ended SFc 10-4 with key
Approved models: OSRAM HTI 700/D4/75
Ballast: electronic
THERMAL
Maximum ambient temperature (Ta): 104° F
Maximum surface temperature: 320° F
Low noise cooling with fan speed regulation mode
Total heat dissipation (calculated, 230 V, 50 Hz / 110 V, 60 Hz): 3190 BTU/hr / 3429 BTU/hr
PHOTOMETRICS
Measurement conditions: 230 V, 50 Hz; no effects applied
Measurement test source: OSRAM HTI 700/D4/75
Photometrics: minimum spread with diffuser
Total output: 14300 lumens
One-tenth peak output: 14300 lumens
Cutoff angle: 16.0°
One-tenth peak angle: 15.0°
Photometrics: median spread with diffuser
Total output: 14600 lumens
One-tenth peak output: 14600 lumens
Cutoff angle: 20.2°
One-tenth peak angle: 19.4°
Photometrics: maximum spread with diffuser
Total output: 14700 lumens
One-tenth peak output: 14700 lumens
Cutoff angle: 30.0°
One-tenth peak angle: 29.0°
Photometrics: minimum spread without diffuser
Total output: 16200 lumens
One-tenth peak output: 16200 lumens
Cutoff angle: 15.8°
One-tenth peak angle: 15.1°
Photometrics: median spread without diffuser
Total output: 16500 lumens
One-tenth peak output: 16500 lumens
Cutoff angle: 20.2°
One-tenth peak angle: 19.5°
Photometrics: maximum spread without diffuser
Total output: 16700 lumens
One-tenth peak output: 16600 lumens
Cutoff angle: 30.6°
One-tenth peak angle: 29.6°
OPTICS
Glass cold light reflector
Spread angle: 14° – 30° (focused on open gobo)
Focal length: 46 – 100 mm
ELECTRICAL
AC input: 3 m trailing cable w/o cord cap
Operating ranges: 100-130/200-250 VAC, 50/60 Hz
Power supply: auto-ranging electronic switch-mode
Main fuse for 200 – 250 V power: 6.3 AT, P/N 05020020
Main fuse for 100 – 130 V power: 15 AT, P/N 05020027
Typical power and current
@ 100 V, 60 Hz: 1019 W, 10.3 A, PF 0.996
@ 120 V, 60 Hz: 988 W, 8.3 A, PF 0.995
@ 208 V, 60 Hz: 949 W, 4.7 A, PF 0.976
@ 230 V, 50 Hz: 944 W, 4.2 A, PF 0.973
@ 240 V, 50 Hz: 940 W, 4.0 A, PF 0.970
@ 250 V, 50 Hz: 940 W, 3.9 A, PF 0.966
V = volts, Hz = hertz, W = watts, A = amps, PF = power factor
Note: Allow for a deviation of +/- 10% from typical figures listed above. Measurements made at nominal
voltage. Local supply voltages can vary by +/- 10%.
CONTROL AND PROGRAMMING
Protocol: USITT DMX-512 (1990)
Control channels: 23 or 31
Receiver: Opto-isolated RS-485
Data I/O: locking 3-pin & 5-pin XLR, pin 1 shield, pin 2 cold (-), pin 3 hot (+)
Setting and addressing: LED control panel or MP-2 uploader
Movement control: tracking and vector
Software installation: serial upload (MUF)
ELECTROMECHANICAL EFFECTS
Beam effects
High speed replaceable rotating 3 facet prism, 8-bit control
Motorized iris, 8- or 16-bit control
Dimmer/shutter
Full-range dimming, 8- or 16-bit control
Shutter speed: flash variable 2hz to 10hz, 8-bit control
Color
1 motorized color wheel with 8 replaceable dichroic color filters, plus open, 8- or 16-bit control
CMY
Cyan: 0-100%, 8- or 16-bit control
Magenta: 0-100%, 8- or 16-bit control
Yellow: 0-100%, 8- or 16-bit control
Pan/tilt
Pan: 540°, 16-bit control
Tilt: 246°, 16-bit control
Position correction system
Gobos
Rotating gobos: 6 positions plus open with continuous and indexed rotation, 16-bit control
Static gobos: 9 positions plus open, 8-bit control
Gobo animation wheel
Vertical, horizontal or angled animation effects.
Indexed and variable speed continuous rotation, 8- or 16-bit control
Focus
Motorized focus: 2m to infinity, 8- or 16-bit control
Zoom
14° – 30°, 8- or 16-bit control
GOBOS
Outside diameter: 27.9 +0/-0.3 mm
Maximum image diameter: 23 mm
Maximum thickness: 1.1 mm in static slots, 4 mm in rotating slots
Recommended glass: high-temperature Borofloat or better with dichroic or enhanced aluminum coating
Recommended metal: 0.5 mm aluminum
GOBO ANIMATION WHEEL
Outside diameter: 116 mm +0/-0.25 mm
Image outer diameter: 112 mm
Image inner diameter: 32 mm
Construction: 0.5 mm aluminum or textured glass with magnet
APPROVALS
EU EMC.EN 55 103-1, EN 55 015, EN 61 547
EU safety: EN 60598-2-17
US safety: ANSI/UL 1573
Canadian safety: CSA C22.2 NO 166
CONSTRUCTION
Housing: UV-resistant fiber-reinforced composite shell
Colors: black
Protection factor: IP 20
Shock resistant chassis
Ergonomic carrying handles
INSTALLATION
Mounting points: 2 pairs of 1/4-turn locks
Orientation: any
Minimum distance from illuminated surface: 48″
Minimum distance from combustible materials: 20″
